Party Shapes, LLC

Stiletto High Heel Shoe Centerpiece is made out of EPS foam in your color choices

The Shoe is 11" tall x 1.5" thick, on a 9" diameter x 1.5" thick base.

The centerpieces are shipped in separate pieces.  

👠 High Heel Stiletto Foam Cutout – Unfinished or Glittered

Add a glamorous touch to your Sweet 16, shopping or diva-themed party decorations with this stiletto heel foam cutout. Perfect for table centerpieces, or event décor.

✨ Glittered Cutouts

• Fully coated in glitter on all sides
• Can be attached to a foam base with a toothpick or bamboo skewer
• Available in custom sizes per listing

Note: Each piece is sprayed with a sealer before shipping, but glitter will still flake off.

🎨 Unfinished Cutouts

• Perfect for DIY decorating, painting, or glittering
• Can be attached to a foam base with a toothpick or bamboo skewer
• Available in custom sizes per listing
• Use only water-based, non-petroleum paints, glues, or coatings
• Bulk discounts available

Note: Use water-based paints (tempera or acrylic) and glue for decorating unfinished foam. Mix paint and school glue, apply, and cover with glitter while wet. Do not use petroleum-based paints or spray paints—they can damage EPS foam. Test new products on a small area first.

9" tall x 1 1/2" thick Stiletto with rhinestone ribbon accent on a 6" base.  Add any number 1-100 to celebrate a milestone occasion.

9" tall x 1 1/2" thick Stiletto with rhinestone ribbon accent on a 6" base.  Add any number 1-100 to celebrate a milestone occasion.

High Heel Shoe Centerpieces cut out of EPS Foam
You will receive one shoe and one base.

Choose the glitter color for the shoe and the glitter color for the base the shoe is sitting on.

The Shoe is 11" tall x 1.5" thick, on a 9" diameter base.
The centerpieces are shipped in separate pieces.
. 

High Heel Shoe Centerpieces cut out of EPS Foam. The 4" tall base is wrapped in silver rhinestone ribbon.
You will receive one shoe and one base.

Choose the glitter color for the shoe and the glitter color for the base.

The Shoe is 9" tall with a 6”x 4" tall base to sit on.
The centerpieces are shipped in separate pieces.
. 

The High-Top shoe is 9-inch-long x 1.5 inches thick sitting on a 6-inch diameter glittered disc. The finished Centerpiece Height - 10-inches.

The first color selection is the color of the shoe.  The second color selection is for the accents on the shoe and the disc it sits on.

The shoes are glittered with a loose glitter that will come off even though we brush and seal it.

The centerpieces are shipped in separate pieces for you to assemble by inserting the attached picks into the base.
. 

Cowboy Boot and Hat Glittered in your choice of colors. Add the base to make a table centerpiece.

Size - 12" tall 9" wide.  Hat and Boot are one piece.

The High-Top shoe is 6-inch-long x 1.5 inches thick sitting on a 6-inch diameter glittered disc. The finished Centerpiece Height - 6-inches.

The first color selection is the color of the shoe.  The second color selection is for the accents on the shoe and the disc it sits on.

The shoes are glittered with a loose glitter that will come off even though we brush and seal it.

The centerpieces are shipped in separate pieces for you to assemble by inserting the attached picks into the base.
. 

11" tall x 1.5" thick EPS foam Football Runner

You can order them unfinished for you to decorate or you can order them in glitter colors.
The items will be glittered on all sides.

Use a foam base & tooth pick to make the figure stand up

Use only water based non-petroleum products. Spray paint can eat the foam.

Use glittered cut outs for a sport or Football themed party decorations.



*

11" tall x 1.5" thick EPS Foam Football Quarterback

You can order them unfinished for you to decorate or you can order them in glitter colors.
The items will be glittered on all sides.

Use a foam base & tooth pick to make the figure stand up

Use only water based non-petroleum products. Spray paint can eat the foam.

Use foam cut outs for a sport or Football themed party decorations.

 11" tall x 1.5" thick Female Runner

Use a toothpick or bamboo skewer to attach to a foam base.

Use only water based non-petroleum products. Spray paint can eat the foam.

Use glittered cut outs for a Track N Field, runner, jogger or sport themed party decorations.


**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

Hurdler Male
12" tall x 1.5" thick EPS Foam Sports Figures.

Choose your glitter color or order it unfinished 


**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

11" tall x 1.5" thick EPS foam Football Kicker.  

Female Basketball Dribbler cut out of 11" tall x 1.5" thick EPS foam

Order unfinished or glittered on all sides in your color choice. If order unfinished, use only water based non-petroleum products. Spray paint can eat the foam.

Use EPS foam cut outs for a basketball, sports party, sports teams themed party decorations.

**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

11" tall x 1.5" thick white Glittered Basketball Female Shooter Cut out

Order unfinished or glittered on all sides in your color choice. If order unfinished, use only water based non-petroleum products. Spray paint can eat the foam.

Use EPS foam cut outs for a basketball, sports party, sports teams themed party decorations.



**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

Use cut outs for a basketball, sports party, sports teams themed party decorations.

11" tall x 1.5" thick Glitterd Female Golfer

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

11" tall x 1.5" thick Glitterd Female Golfer

11" tall x 1.5" thick Ballerina cut out

You can order them unfinished for you to decorate or you can order them in glitter colors.
The items will be glittered on all sides.

Use a foam base & tooth piece to make the figure stand up

Use only water based non-petroleum products. Spray paint can eat the foam.

Contact us if you need the items finished with a color, larger, or custom shapes.

Use Party Shapes cut outs for a Ballerina party, sports end of the year banquet, cheer themed party decorations.

**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

Ballerina Figure cut out of EPS foam 11"tall x 1.5" thick.
Order glittered or unfinished.

Attach to a foam base by inserting and gluing a toothpick or bamboo skewer.

 Great for a dance recital, prom, or any special celebration

Use foam cut outs for a birthday party, end of the year banquets, ballerina themed party decorations.

**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

11" tall x 1.5" thick white Glittered Basketball Female Shooter Cut out

Order unfinished or glittered on all sides in your color choice. If order unfinished, use only water based non-petroleum products. Spray paint can eat the foam.

Use EPS foam cut outs for a basketball, sports party, sports teams themed party decorations.



**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

Use cut outs for a basketball, sports party, sports teams themed party decorations.

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Female Basketball Dribbler cut out of 11" tall x 1.5" thick EPS foam

Order unfinished or glittered on all sides in your color choice. If order unfinished, use only water based non-petroleum products. Spray paint can eat the foam.

Use EPS foam cut outs for a basketball, sports party, sports teams themed party decorations.

**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

11" tall x 1.5" thick EPS foam Football Kicker.  

11" tall x 1.5" thick EPS foam Football Runner

You can order them unfinished for you to decorate or you can order them in glitter colors.
The items will be glittered on all sides.

Use a foam base & tooth pick to make the figure stand up

Use only water based non-petroleum products. Spray paint can eat the foam.

Use glittered cut outs for a sport or Football themed party decorations.



*

11" tall x 1.5" thick EPS Foam Football Quarterback

You can order them unfinished for you to decorate or you can order them in glitter colors.
The items will be glittered on all sides.

Use a foam base & tooth pick to make the figure stand up

Use only water based non-petroleum products. Spray paint can eat the foam.

Use foam cut outs for a sport or Football themed party decorations.

Create your own custom decorations with our Unfinished Ballerina Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Add a base for $6.00. Add Glittered Base $6.00 – Party Shapes, LLC

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________